PAK2116.1000
Bowden cable with plastic bush, D=M06, L=1000, Stainless steel, Components: plastic
Estimated delivery: On request
Material:
Stainless steel wire rope 1.4401.
Cover for cable sheathing in stainless steel.
Bush for end applications, set screw and threaded nipple made of brass.
Stainless steel hexagon nut A2.
Version:
Wire rope and hexagon nut, untreated surface.
Cover for cable sheathing in black plastic.
Bush for end applications, blue passivated.
Brass adjusting screw and threaded terminal.
Order example:
K2116.3000
Note:
Bowden cables are intended for the transmission of tensile force and are used as remote control in combination with actuating elements.
The Bowden cable is available in different length variants. To ensure a precise fit in the respective application, the Bowden cable can be shortened during mounting.
The following points must be observed when assembling Bowden cables:
The length of the free end of the cable may vary due to factors such as the mounting angle, bending radius and load. The length of the counter-bearing (cable sheath) must therefore be adjusted, after the Bowden cable has been installed, using the adjusting screw included. The preload of the Bowden cable system is adjusted simultaneously with the adjusting screw.
During assembly, particular care must be taken to ensure that the minimum bending radius, in this case R = 65 mm, is not undercut. A radius that is too narrow can lead to increased wear and friction.
The minimum bending radius must also not be undercut during installation, otherwise the cable sheath will be damaged. In addition, the cable sheath is designed only to absorb compressive forces: if it is pulled too hard, the inner coil will be stretched and permanently damaged.
The Bowden cable is a spare part for remote-controlled indexing plungers K1502.
Scope of delivery:
Wire rope with terminal K2023.
Cover for cable sheathing with inner tube K2024.
Bush for end applications K2025.
Adjusting screw K2026.
Threaded mounting end with threaded pin K2027.
Hexagon nut K0700.106.
Accessories:
Indexing plunger and actuating element K1502.
Drawing note:
1) Wire rope
2) Cover for cable sheathing
3) Bush for end applications
4) Adjusting screw
5) Threaded terminal
6) Hexagon nut
Stainless steel wire rope 1.4401.
Cover for cable sheathing in stainless steel.
Bush for end applications, set screw and threaded nipple made of brass.
Stainless steel hexagon nut A2.
Version:
Wire rope and hexagon nut, untreated surface.
Cover for cable sheathing in black plastic.
Bush for end applications, blue passivated.
Brass adjusting screw and threaded terminal.
Order example:
K2116.3000
Note:
Bowden cables are intended for the transmission of tensile force and are used as remote control in combination with actuating elements.
The Bowden cable is available in different length variants. To ensure a precise fit in the respective application, the Bowden cable can be shortened during mounting.
The following points must be observed when assembling Bowden cables:
The length of the free end of the cable may vary due to factors such as the mounting angle, bending radius and load. The length of the counter-bearing (cable sheath) must therefore be adjusted, after the Bowden cable has been installed, using the adjusting screw included. The preload of the Bowden cable system is adjusted simultaneously with the adjusting screw.
During assembly, particular care must be taken to ensure that the minimum bending radius, in this case R = 65 mm, is not undercut. A radius that is too narrow can lead to increased wear and friction.
The minimum bending radius must also not be undercut during installation, otherwise the cable sheath will be damaged. In addition, the cable sheath is designed only to absorb compressive forces: if it is pulled too hard, the inner coil will be stretched and permanently damaged.
The Bowden cable is a spare part for remote-controlled indexing plungers K1502.
Scope of delivery:
Wire rope with terminal K2023.
Cover for cable sheathing with inner tube K2024.
Bush for end applications K2025.
Adjusting screw K2026.
Threaded mounting end with threaded pin K2027.
Hexagon nut K0700.106.
Accessories:
Indexing plunger and actuating element K1502.
Drawing note:
1) Wire rope
2) Cover for cable sheathing
3) Bush for end applications
4) Adjusting screw
5) Threaded terminal
6) Hexagon nut
| Material | Stainless steel |
|---|---|
| Thread | M6 |
| SW | 10 |
|---|---|
| L | 1000 |
| D | M6 |
| D3 | 5 |
| D2 | 5 |
| L1 | 1200 |
| D1 | 1,5 |
| B | 7 |
| Versão 1 | com casquilho de plástico |
| Material dos componentes | plástico |
| Denominação | Cabo Bowden |
