PAK2047.042612084
Indexing plunger with eyelet grip TA.2 D1=M12, D=6, Style D with latching groove with lock nut, Non-hardened steel
Estimated delivery: On request
Indexing plungers are used when it is necessary to prevent a change in the locking position due to lateral forces. It is only possible to move to another locking position after the pin has been disengaged manually.
If the disengagement is carried out over a longer period of time and the guided locking pin must not return, form C or form D should be used.
Material:
Steel version:
Threaded bush in free-cutting steel.
Guide pin for locking 1.4305.
Stainless steel version:
Threaded bush and locking guide pin 1.4305.
Eyelet knob in thermoplastic.
Version:
Steel version:
Blue passivated threaded bush.
Unhardened guide pin for locking, untreated surface.
Stainless steel version:
Threaded bush, untreated surface.
Unhardened guide pin for locking, untreated surface.
Eyelet knob in dark grey RAL 7021 or traffic red RAL 3020.
Note:
During assembly, the max. tightening torque must be observed. specified.
On request:
Special versions.
Drawing note:
Form A: without locking groove, without lock nut
Form B: without locking groove, with lock nut
Form C: with locking groove, without lock nut
Form D: with locking groove, with lock nut
If the disengagement is carried out over a longer period of time and the guided locking pin must not return, form C or form D should be used.
Material:
Steel version:
Threaded bush in free-cutting steel.
Guide pin for locking 1.4305.
Stainless steel version:
Threaded bush and locking guide pin 1.4305.
Eyelet knob in thermoplastic.
Version:
Steel version:
Blue passivated threaded bush.
Unhardened guide pin for locking, untreated surface.
Stainless steel version:
Threaded bush, untreated surface.
Unhardened guide pin for locking, untreated surface.
Eyelet knob in dark grey RAL 7021 or traffic red RAL 3020.
Note:
During assembly, the max. tightening torque must be observed. specified.
On request:
Special versions.
Drawing note:
Form A: without locking groove, without lock nut
Form B: without locking groove, with lock nut
Form C: with locking groove, without lock nut
Form D: with locking groove, with lock nut
| Material | Steel |
|---|---|
| Finishing | Unhardened |
| Thread | M12 |
| F x 30° | 1,8 |
|---|---|
| SW2 | 19 |
| Força de mola final F2 aprox. N | 15 |
| Força de mola inicial F1 aprox. N | 8 |
| L | 61,7 |
| D | 6 |
| L2 | 34 |
| SW1 | 12 |
| Curso S | 6 |
| A | 30 |
| L1 | 20 |
| Binário de aperto máx. Nm | 20 |
| D1 | M12 |
| B | 8 |
| L3 | 17 |
| Cor dos componentes | vermelho RAL 3020 |
| Tamanho | 2 |
| Forma | D |
| Versão 2 | com manípulo tipo ilhó |
| Versão 1 | com ranhura de engate |
| Material dos componentes | termoplástico |
| Denominação | Pino de indexação |
| Tipo de produto | padrão |
| Contraporca | com contraporca |
| Tipo de forma | com ranhura de engate com contraporca |
