PAK1425.12712
Oil level indicator with electronic monitoring of D1=M12 164X42X21 plastic, Normally open contact
Estimated delivery: On request
Material:
Housing in glass-fibre-reinforced thermoplastic polyamide.
Thermoplastic polyamide sight window
Rubber (NBR) O-ring and flat sealing ring.
PVC plastic reflector.
Plastic float.
Screw and hexagon nut, steel.
Version:
Black housing.
Transparent sight window with high mechanical strength and durability.
White reflector.
Red float with magnet.
Zinc-plated screw and hexagon nut.
Order example:
K1425.12712
Note:
With the oil level indicator, the filling level can be viewed and detected by means of a reed switch.
As soon as the float reaches the defined minimum value, an electrical signal is emitted after the electrical circuit closes.
The sensor is positioned on the housing and its height can be adjusted according to the level control requirements. A
the minimum specification is approx. 35 mm from the centre of the lower fixing screw.
The reed switch is equipped with a normally open (NO) contact.
The sight glass consists of two transparent components, ultrasonically welded after assembly, thus ensuring a seal
integral.
The maximum pressure corresponds to 1 bar. Tightening torque of the fixing screws 5Nm.
The sight glass has good mechanical resistance and is compatible with mineral oil, petrol, lubricants, kerosene, solvents and most chemical agents. Avoid contact with alcoholic solutions and hot water.
Temperature range:
Maximum operating temperature: 75 °C.
Mounting:
The oil level indicator is fixed by two threaded holes M12 or, alternatively, by two holes of Ø 12,2 mm (± 0,2 mm) with flange nuts. Centre distance of the mounting holes = L1 ±0,3.
Functions:
The oil is measured by means of a magnetic float, which activates the electrical contact when it reaches the “REED” level switch. If the oil level drops below a certain level, an electrical pulse can be emitted.
Observe:
Strong magnetic fields affect operation.
Technical data:
See Downloads, Technical note.
Drawing note:
1) Viewing window
2) O-ring
3) Flange nut M12
4) Housing
5) Flat sealing ring
6) Float with magnet
7) Hollow screw M12
8) Reed switch
Housing in glass-fibre-reinforced thermoplastic polyamide.
Thermoplastic polyamide sight window
Rubber (NBR) O-ring and flat sealing ring.
PVC plastic reflector.
Plastic float.
Screw and hexagon nut, steel.
Version:
Black housing.
Transparent sight window with high mechanical strength and durability.
White reflector.
Red float with magnet.
Zinc-plated screw and hexagon nut.
Order example:
K1425.12712
Note:
With the oil level indicator, the filling level can be viewed and detected by means of a reed switch.
As soon as the float reaches the defined minimum value, an electrical signal is emitted after the electrical circuit closes.
The sensor is positioned on the housing and its height can be adjusted according to the level control requirements. A
the minimum specification is approx. 35 mm from the centre of the lower fixing screw.
The reed switch is equipped with a normally open (NO) contact.
The sight glass consists of two transparent components, ultrasonically welded after assembly, thus ensuring a seal
integral.
The maximum pressure corresponds to 1 bar. Tightening torque of the fixing screws 5Nm.
The sight glass has good mechanical resistance and is compatible with mineral oil, petrol, lubricants, kerosene, solvents and most chemical agents. Avoid contact with alcoholic solutions and hot water.
Temperature range:
Maximum operating temperature: 75 °C.
Mounting:
The oil level indicator is fixed by two threaded holes M12 or, alternatively, by two holes of Ø 12,2 mm (± 0,2 mm) with flange nuts. Centre distance of the mounting holes = L1 ±0,3.
Functions:
The oil is measured by means of a magnetic float, which activates the electrical contact when it reaches the “REED” level switch. If the oil level drops below a certain level, an electrical pulse can be emitted.
Observe:
Strong magnetic fields affect operation.
Technical data:
See Downloads, Technical note.
Drawing note:
1) Viewing window
2) O-ring
3) Flange nut M12
4) Housing
5) Flat sealing ring
6) Float with magnet
7) Hollow screw M12
8) Reed switch
| Material | Plastic |
|---|---|
| Thread | M12 |
| Versão 2 | NO |
|---|---|
| Versão 1 | com monitorização eletrónica do nível de óleo |
| Material dos componentes | aço |
| Denominação | Indicador do nível de óleo |
| H | 21 |
| H1 | 21 |
| L2 | 91 |
| D1 | M12 |
| Quantidade de parafusos de fixação | 2 |
| B | 42 |
| SW | 19 |
| L | 164 |
| L1 | 127 |
| L3 | 75 |
Product Variations
| Model | Material | Thread | Versão 2 | Versão 1 | Material dos componentes | Denominação | H | H1 | L2 | D1 | Quantidade de parafusos de fixação | B | SW | L | L1 | L3 | Stock | Quantity | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| PAK1425.12712 PAK1425.12712 | Plastic | M12 | NO | com monitorização eletrónica do nível de óleo | aço | Indicador do nível de óleo | 21 | 21 | 91 | M12 | 2 | 42 | 19 | 164 | 127 | 75 | |||
PAK1425.12712
Oil level indicator with electronic monitoring of D1=M12 164X42X21 plastic, Normally open contact
Material = Plastic
Thread = M12
Versão 2 = NO
Versão 1 = com monitorização eletrónica do nível de óleo
Material dos componentes = aço
Denominação = Indicador do nível de óleo
H = 21
H1 = 21
L2 = 91
D1 = M12
Quantidade de parafusos de fixação = 2
B = 42
SW = 19
L = 164
L1 = 127
L3 = 75