PAK1742.16
Pneumatic hole clamping and centring element, D1=16, D=20, M03, Stainless steel, Components: Buna N
Estimated delivery: On request
The workpiece is clamped and released by means of compressed air.
The possible clamping diameter is between 16–20 mm.
Material:
Main body in stainless steel.
NBR seal.
Version:
Stainless steel, untreated surface.
Order example:
K1742.16
Ordering note:
The cheese-head screws M4 x 35 for fastening from below are included in the scope of delivery.
The low-head cheese-head screws M5 for fastening from above are not included in the scope of delivery.
Note:
Mounting dimensions for sheets 6 mm thick.
The holding forces specified refer to an operating pressure of 0,5 MPa and a surface finish quality of Ra 1,6 µm.
The repeatability is approx. ± 0,2 mm.
Drawing note:
1) "Clamping" position
2) "Loosening" position
3) Clamping plate
4) O-ring
5) "Clamping" connection
6) "Loosening" connection
7) Cheese head screw M4
8) Low cheese head screw M5
9) Workpiece
The possible clamping diameter is between 16–20 mm.
Material:
Main body in stainless steel.
NBR seal.
Version:
Stainless steel, untreated surface.
Order example:
K1742.16
Ordering note:
The cheese-head screws M4 x 35 for fastening from below are included in the scope of delivery.
The low-head cheese-head screws M5 for fastening from above are not included in the scope of delivery.
Note:
Mounting dimensions for sheets 6 mm thick.
The holding forces specified refer to an operating pressure of 0,5 MPa and a surface finish quality of Ra 1,6 µm.
The repeatability is approx. ± 0,2 mm.
Drawing note:
1) "Clamping" position
2) "Loosening" position
3) Clamping plate
4) O-ring
5) "Clamping" connection
6) "Loosening" connection
7) Cheese head screw M4
8) Low cheese head screw M5
9) Workpiece
| Material | Stainless steel |
|---|
| H2 | 11,3 |
|---|---|
| B2 | 5 |
| H3 | 6 |
| L | 40 |
| H8 | 13 |
| H9 | 18 |
| H | 10 |
| H1 | 14,7 |
| L2 | 18 |
| B1 | 28 |
| D | 20 |
| H4 | 17,5 |
| D3 | M3 |
| Força de retenção N | 77 |
| D2 | M5 |
| H5 | 10 |
| L1 | 22 |
| D5 | 4,2 |
| D4 | M3 |
| B3 | 5 |
| H6 | 30 |
| H7 | 40 |
| D1 | 16 |
| B | 36 |
| B4 | 7,5 |
| L3 | 8 |
| Versão 1 | pneumático |
| Material dos componentes | Buna N |
| Denominação | Elemento de fixação e centragem em furos |
| Pressão de funcionamento MPa | 0,3 - 0,7 |
Product Variations
| Model | Material | H2 | B2 | H3 | L | H8 | H9 | H | H1 | L2 | B1 | D | H4 | D3 | Força de retenção N | D2 | H5 | L1 | D5 | D4 | B3 | H6 | H7 | D1 | B | B4 | L3 | Versão 1 | Material dos componentes | Denominação | Pressão de funcionamento MPa | Stock | Quantity | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| PAK1742.16 PAK1742.16 | Stainless steel | 11,3 | 5 | 6 | 40 | 13 | 18 | 10 | 14,7 | 18 | 28 | 20 | 17,5 | M3 | 77 | M5 | 10 | 22 | 4,2 | M3 | 5 | 30 | 40 | 16 | 36 | 7,5 | 8 | pneumático | Buna N | Elemento de fixação e centragem em furos | 0,3 - 0,7 | |||
PAK1742.16
Pneumatic hole clamping and centring element, D1=16, D=20, M03, Stainless steel, Components: Buna N
Material = Stainless steel
H2 = 11,3
B2 = 5
H3 = 6
L = 40
H8 = 13
H9 = 18
H = 10
H1 = 14,7
L2 = 18
B1 = 28
D = 20
H4 = 17,5
D3 = M3
Força de retenção N = 77
D2 = M5
H5 = 10
L1 = 22
D5 = 4,2
D4 = M3
B3 = 5
H6 = 30
H7 = 40
D1 = 16
B = 36
B4 = 7,5
L3 = 8
Versão 1 = pneumático
Material dos componentes = Buna N
Denominação = Elemento de fixação e centragem em furos
Pressão de funcionamento MPa = 0,3 - 0,7